IMPORT PXF unable to ISO Support and Attachments
I know about the item #16, but my PXF has positive values for 2106. example below. Any other ways to reattach or redraw the supports and misc attachements using tools. Manually redrawing allows...
View ArticleClik here to view.
OPM SS6 - monolithic joint
Hi,Is there already a OPM component that I can as a monolithic joint? If not, which would be the best template to base a monolithic joint on? Below is an example monolithic joint that is similar to...
View ArticleOPM SS6 - How to create joint between PE/BW ends with PFS ends?
Hi,I've create a custom component with PFS end, and that component is set to act as a push fit cap to ends of pipe. However, the component won't go (or snap) on the ends of pipe with either PE or BW...
View ArticleHow to show insulation along a pipe not the whole pipe?
How can you show Insulation along a pipe but no the whole pipe?Personal protection insulation is usually around 2.4m above the ground and below, where a pipe runs from within this level to higher, the...
View ArticleOPM SS6 - bolt missing between LUG butterfly valve and RF flanges
Hi,I created a butterfly valve with LUG conditions at both ends. When I try to connect the valve to an RF flange, the bolt is missing, only the gasket is placed. Any suggestion as to what is missing?...
View ArticleOPM SS6 - Standard mEX-OPM spec's butterfly valve is missing
When I ran a test using the standard OPM_Metric project and mEX-OPM spec, I couldn't place butterfly valve of any size. The program through the usual "No component found with initial selection from...
View ArticleHow to get pipe/elbow connect point's coordinate in MVBA
Hello All,I'd like to get the coordinate of connect points of pipe/elbow. I did scan the property of OPM imodel (PropertyHandler), I find TRANSFORMATION_MATRIX.M03/07/11 are x/y/z of one connect point,...
View ArticleClik here to view.
Dummy Lag Support - Origin Location
When a Dummy Leg Support is placed on a pipe, the origin of the support is some random number away from the actual origin of where it should be.How is OPM calculating the origin of the support and what...
View ArticleOpenPlant Isometrics Customisation
Good Day AllWhen I started working on Bentley software we could customise Isogen to populate the Isometric border sheet with a Attribute file. Instead of typing all your information into the border...
View ArticleHow can I generate single line BOP in OPM?
Please suggest how can I generate BOP for a single line out of total project ?(If I have revised that particular line and need to generate grid report for that single line).
View ArticleAutoPLANT i-model, which Navigator version
Hi,AutoPLANT SS7r1 (.239)AutoPLANT i-model Composer (.129)ProjectWise SS4 (.590)Navigator Connect (6.1.1.52)I'm trying to view an i-model created from a piping model. Navigator shows error message...
View ArticleIntelligent Line Manager Default settings
I am experimenting with the Intelligent Line Manager command in both SS5 and SS6.The command always opens with the corner option as Pipe Bend, which is not what our industry would most commonly use. We...
View ArticleClik here to view.
AutoPlant Model File Errors - Need Help To Resolve
Hello,The piping model I was updating unexpectedly received errors when launching AutoPlant. I was using AutoPlant without any issues one minute, closed down the model to rerun the Navisworks file...
View ArticleAutoPLANT Modeler, Lined Pipe, Bolt Calculation
Hi,AutoPLANT Modeler SS7r1 (.239)Lined Pipe ModuleBolt calculation is not done when inserting two fittings. Works fine when something is in between the flanges.Calculated Bolt Length is set to YesSH
View Articlesystem Requeriments
hello. I would like to know the requirements of my system to install autoplant
View ArticleOPM - Pipe Insulation Saddle adjust angle
Hi,Is there a way to control the angle of wrap around the pipe with this kind of support?It seems to be hard set to 90deg, I would like to have the ability to increase/decrease this.ThanksRay
View ArticleAP OPIM - Victaulic Coupling behave differently while placing order differently
When placing Vic coupling, ie, Vic Coupling Rigid 07, in different way, it shows and differently in OPIM ISOop 1- place a vic pipe, place a rigid 07 coupling, place another vic pipe- vic coupling...
View ArticleClik here to view.
OPM SS6 - Copy components from i.dgn references
Hi,Base on the answer from the FAQ here:When I tried to copy components from a reference. The new components are there, but no pipeline is created in the pipeline manager. And as such, I cannot...
View ArticleProblem with print organizer oppid
Hello,I have a problem with the print organizer in OPPID, when i add the active file to set i received un error message : Exception encountered inside WorkerMicroStationProxy.LoadDesignFile. Can...
View ArticleClik here to view.
Combining supports types in OPIM BOM
In some of our isometrics, there are several supports that are identical. They are each listed individually as separate items in the BOM. Most often these supports are a generic item like a support...
View Article